GfA Elektromaten ST 80.15 Sliding Gate Drive 800 Nm, output shaft right, horizontal installation
€2,149.00
Product information "GfA Elektromaten ST 80.15 Sliding Gate Drive 800 Nm, output shaft right, horizontal installation"
ST-ELEKTROMATEN, Drive for industrial sliding gates, output torque 800 Nm, output speed 15 rpm, max. door weight 80000 N, supply voltage 3~230V/400V, output shaft ø 50 mm, with the following configuration:
- Output Shaft: right
- Installation position: horizontal
- Magnetic brake: without
- Integrated limit switch: without
- Control unit: without
Explanation:
- Output shaft: The output shaft can be mounted on the left or right. The correct side is determined by looking at the top of the drive from the motor in the direction of the gearbox. Subsequent changes to the output shaft are not possible.
- Installation position: The drive is mounted either horizontally or vertically on a foot bracket. Please also refer to the technical drawing above.
- Magnetic brake: We recommend operating the drive with a magnetic brake, otherwise the gearbox will be heavily loaded.
- Limit switch: The operator can be ordered without limit switch, with integrated digital limit switch DES or with integrated mechanical limit switch NES. An external limit switch is available as an accessory. With an integrated limit switch, the limit switch range (E=20, E=40 or E=60 revolutions, depending on the drive variant) can be selected. These values refer to the maximum possible revolutions of the output shaft.
- Control unit: You can order the drive without a control unit or optionally with an integrated WS 905 control unit. The operator can also be operated with an external control unit, e.g. the GfA Elektromaten TS 400. This is available as an accessory.
Description:
The GfA Elektromaten ST 80.15 sliding gate operator , with a drive torque of 800Nm and an output speed of 15 rpm is an operator for industrial sliding gates. The sliding gate operator consists of a worm gear with integrated slipping clutch, output shaft on the right, mounting and electric motor. The operator is installed in a horizontal position.
The following components are not included in the scope of delivery and can be ordered optionally with the operators:
- Emergency manual operation - e.g. for top-running sliding gates: Emergency hand crank NHK or chain emergency hand KNH
- External limit switch - roller lever limit switch or inductive limit switch
If you require one of these additional options, please contact us for a customized offer.
The integrated GfA Elektromaten WS 905 control unit can be ordered as an option. This has a control voltage of 24V AC and is equipped with 2 contactors. The cable length to the operator is 0.8m (CEE plug is not included).
The WS 905 can be operated with mechanical limit switches NES or with external limit switches. The digital limit switch DES is not compatible with the WS 905. In this case, an external control unit such as the GfA Elektromaten TS 400 is required.
| Gate Speed (with standard sprocket): | 12 cm/sec |
|---|---|
| Hollow- / Output-Shaft (Ø): | 50 mm |
| Max. output speed CLOSE for frequency inverter operation: | 26 min^-1 |
| Max. output speed OPEN for frequency inverter operation: | 26 min^-1 |
| Output Speed: | 15 min^-1 |
| Output Torque: | 800 Nm |
| Power: | 1.1 kW |
| Supply Voltage: | 3~230/400 V |
| max. Door Weight: | 80000 N |
| max. Movements per Hour: | 10 |
Login
Other customers also bought
Sensing Egde Set Type ASO Safety SENTIR Edge 35.55 CT, Set includes rubber profile and all accessories needed to build a safety edge with a length of 1,5m as end or serial edge, cable length 2,5m, includes aluminium c-profile, assembly without the use of glue or additional assembly materials Description: The Plug’N’Sense System allows easy assembly of the SENTIR Edge 35.55 CT contact edges by ASO Safety. No additional adhesive or other assembly material is needed. The safety edges can be assembled on site, allowing for tailor made solutions according to the local conditions. The safety edge sets contain all the necessary materials to produce end and serial edges. As a terminating resistor the end plugs are equipped with an 8k2 ohm resistor, which can be monitored by many of the commercially available gate and door controls. The safety edge set includes: 1,5m contact profile SENTIR Edge 35.55 CT, width 35mm, height 55mm 2 x 0,75m aluminium profile AL 35-14, width 35mm, height 14mm 2 x lock cap 1 x resistor plug 8.2 kOhm 2 x connector with cable 2,5m 2 x end cap 35.55 4 x fixation clips On request, we also deliver pre-assembled safety edges according to your desired length. Please send us your requirements and we will make an individual offer.
Inductive signal transmission unit, incl. Control unit in housing for surface mounting, moving and staionary coil cores, 20m steel cable and cable tensioner unitDescription:The INDUS compact classic 74-312 Set S by ASO Safety is an inductive signal transmission system for resistive sensing edges with 8,2 kOhm resistance. Its main application is to transmit the signal from the main, moving sensing edge on gates to the stationary gate control unit. The system works with inductive technology and thereby does not need batteries for power supply. Properties:Inductive signal transmission works without batteriesSupply voltage 24 V AC/DC or 230 V ACSafety category 3/ PL „e“ acc. to EN ISO 13849 Included in the box:Control unit INDUS classic 74-312 in housing for surface mountingMoving coil core SPK 54 SStationary coil core SP 55, incl. Installation bracket20m steel cable, with 2 additional conductorsCable tensioning unit
Motor cable for GfA Elektromaten drives with digital limit switch DES, length 3m
Gate control unit for GfA Elektromaten sliding gate drives with digital or mechanical limit switch, automatic or constant pressure to close operation, in plastic housing with transparent lid
reflective photo eye, max. range 9m, supply voltage 24 ... 240 V AC/ 12 ... 240 V DC, signal output: changeover relay, IP67 rated, 2m connection cableDescription:Universal Reflective Photo-eye barrier for contactless protection of industrial doors. The light barrier works on an extremely wide supply voltage range and through the execution of the output signal as a changeover relay (Normally Closed Contact and Normally Open Contact), it is compatible with most door control units.The photo-eye sensor works with visible red lights (630nm wavelength) and has a built-in polarisation filter. Through this, the photo-eye sensor is extremely impervious to external light and is easy to install.Coverage up to 9mUniversal power supply voltage AC 24 to 240V, DC 12 to 220V2m connection leadRelay output (changeover)
Accessories
Motor cable for GfA Elektromaten drives with digital limit switch DES, length 3m
Gate control unit for GfA Elektromaten sliding gate drives with digital or mechanical limit switch, automatic or constant pressure to close operation, in plastic housing with transparent lid
Motor cable for GfA Elektromaten drives with mechanical limit switch NES, length 3m
Housing for GfA Elektromaten Sliding Gate Drives type ST, for right- or left-hand use
Sprocket for GfA Elektromaten drives, inner diameter hollow shaft 50mm, width 16,2mm, 19 teeth