Sensors

Hormann Art. Nr. 637515, conversion kit SKS board for control unit WA 100 / 200, consisting of: Replacement board SKS for WA 100 / 200, optosensor transmitter BR 40, optosensor receiver BR 40, 2 x adapter sleeves; production period 15.12.2006 -

Airwave switch, changeover contact, with mounting bracketDescription:The FRABA VITECTOR DW3O-420 airwave switch converts the pressure wave from a signal transmitter (e.g. push button, rubber pressure sensing strip, rubber profile) into an electrical switching signal. These FRABA VIECTOR airwave switches are installed in the most diverse applications.Properties:Contact type: Changeover, opens or closes upon contact with the switching mechanismWith screw connection

Travelling coil core for door for indoor installationDescription:The ELMON Inductive SPK 52.2 by ASO Safety is a travelling coil core for the signal transmission system ELMON Inductive, for internal installation.Technical properties:• For connection to the SPE 3 electronic connection device• Measurements (W x H x D): 21 mm x 21 mm x 50 mm

Control unit for ELMON Inductive 74-312 as a replacement part for the ELMON Inductive system, housing for surface-mountDescription:The ELMON Inductive 74-312 by ASO Safety a control unit for monitoring the status of safety edges in the ELMON Inductive signal transmission system.Technical properties:• Supply voltage 24 V AC / DC, 230 V AC ± 10%• Safety category 3/ PL “e” acc. to EN ISO 13849-1:2008• Wall mounting with clear plastic cover case

Hormann Art. Nr. 638378, pre-travelling light barrier VL2 with protective cover, receiver inside right for VL 2; Note: For VL 2 before July 2007 you have to exchange transmitter and receiver, not compatible with transmitter or receiver VL1-LE, not compatible with radio connecting cable, marking: black connecting cable, production period 01.11.2005 - 31.12.2018

Control unit to monitor up to 2 optical sensing edges OSE, relay output (Stop, Alarm), supply voltage 24 V DC, DIN-rail enclosure, width 25mm, rated cat. 1 PL c (EN 13849-1)Description:The FRABA VITECTOR OSE-C 4524 is a control unit for optical sensing edges on machines and doors. The control unit monitors up to two (FRABA VITECTOR OSE -type) optical sensing edges and converts the safety signal of the sensors into potential-free NC relay contact. In addition to the safety output, the OSE-C 4524 also provides another signalling contact (Relay, changeover contact) e.g. for a higher level of control.Housing in a DIN-rail mounting enclosureHousing protection class: IP40, Terminal Block IP 20Supply Voltage 24 V DCSafety Category: Cat. 1 PLc according to EN13849-1

Unidirectional radar motion detector for universal opening, adjustable via remote (separate accessory), narrow or wide detection field, 10 different field sizes, IP54 rated, 2,5m cable, installation height 4,0 - 5,0mDescription:The EAGLE radar scanner from BEA offers a solution for any type of automatic door, regardless of environmental conditions. The EAGLE ONE is a unidirectional motion sensor for standard automatic doors. The EAGLE ONE HM can be mounted at an installation height of up to 5m. The configuration of parameters is flexible and easy thanks to the remote control unit or push buttons.Characteristics:• Improves the overall energy efficiency of the buildings thanks to its unidirectional motion sensor. The sensor only captures the movement of objects approaching the door and ignores the ones moving away. This way, the door closes earlier, reducing the loss of heat or air-conditioned temperature.• The size and shape of the detection field can be adapted to the environment and application.• Thanks to the BEA radar antenna and the unidirectional sensor, the EAGLE ONE offers stability and reliability.

Set Transmitter (Tx) and Receiver (Rx) for Optical Sensing Edge OSE, PUR-cable, cable length 10,5m/3,0m, without plugsDescription:The FRABA VITECTOR OSE-S1100 sensor set consists of a transmitter (Tx) and a receiver (Rx) for optical sensing edges. The sensors are equipped with a top quality PUR Cable (length: transmitter - 10.5 m and receiver - 3.0m). For an electrical connection, the sensors are based on the original FRABA OSE technology and provide the well-known OSE-signal, which is implemented in many controllers.Warning:The 4-digit sequence of numbers used on the displays shows the sensor's manufacture date in week / year format. For example, 0118 shows the sensor was produced in the first calendar week (01) of 2018.

2 channel loop detector for vehicle detection, power supply 100-240 V AC, with USB-interface and modern diagnostics- and service-software, in plastic enclosureDescription:The loop detector VEK MNE2-R230-C from FEIG Electronic is used to monitor induction loops to detect vehicles at barriers, traffic lights, etc. The device is 2-channel and can monitor two loops. The integrated USB interface allows the device to be connected to the PC and the advanced diagnostic and service software simplifies installation and maintenance of the device.Properties:USB interface to use the modern diagnostics and service softwareimproved detection speed and flexibilityAutomatic adjustment at power up or at resetDetection of travel directionConnection via 11-pin socket for mounting on DIN railrelay operating principle selectable

Set Transmitter (Tx) and Receiver (Rx) for Optical Sensing Edge OSE, PUR-cable for energy-chains, cable length 10,5m/10,5m

Rubber profile for optical sensing edges, coil of 5m, material EPDM

Control unit for 8k2-Safety Edges, housing for surface mounting, 230 V, 24 AC/DC, safety level cat. 3/ PL "e"Description:The control unit ELMON classic 32-312 by ASO Safety is used to monitor the status of 8k2-sensing edge. The unit can monitor up to 2 sensors with 8k2 end resistor and has two separate output relays to indicate sensor status. Properties:Housing for surface mountingSupply voltage 230V, 24 V AC/DC, +/- 10%Reaction time < 12 msInput: 2 sensor signals, 8,2 kOhmOutput: 2 forcibly guided, redundant relaysHousing with clear lidSafety category 3/ PL „e“ acc. to EN ISO 13849-1:2008Dimensions: 120 x 102 x 55 mm (WxHxD)

Product description: Novoferm Extra 626 two-wire photo eyeNovoferm Extra 626 photoelectric sensor, output: 2-wire, range 8 m for indoor areas     Simple installation: The two-wire technology and the connection with any polarity enable effortless integration into various door operators.     Large monitoring range: With a range, coverage of 8 m, the photo eye provides reliable protection against obstacles.     Easy teach-in: The position of the photo eye can be easily taught-in to ensure precise function.     Function indicators with LED: Thanks to the LED indicators, you can check the status of the photo eye at a glance.     With daylight cut-off filter: The integrated daylight cut-off filter ensures reliable operation regardless of the lighting conditions.     For indoor use: The photo eye is specially designed for indoor use to ensure a long service life and reliable functionality. The LS2-I photo eye is compatible with a wide range of door operators, including:     Tormatic WHITE series     Tormatic BLACK series     NovoPort III     Novomatic 553 S     ATS 24 III     Novomatic 803 S     GTA 701 NRG     GTA 702 NRG     GTA 702 S     GTA 802 S     GTA 803 S

Hormann Art. Nr. 638461, Pull-in protection EZS / transmitter, Sealing compound: black, IP54, cable length: 1500 mm; Production period 01.03.2005 -

Hormann Art. Nr. 635704, pre-travelling light barrier VL2-LE, Set, with sliding plates, range 6,0 - 10 m; Note: marking LE: grey connecting cable, production period 01.03.2017 -   Product description: The Hormann VL2-LE sensor system is a 2-beam travelling photo eyes and is used to safeguard compatible industrial sectional doors. The 2-beam photo eye is guided in front of the lower edge of the door by the supplied mechanism and if a light beam is interrupted by an obstacle, the door is stopped and reversed. The ‘LE’ system (grey connection cable with yellow/blue system plug) replaces the old VL2 systems without ‘LE’ (black connection cable with transparent system plug). Note: Identification sensor type ‘LE:’ grey connection cable, production period 01.03.2017 - LE transmitter & receiver: blue system plug The sensor type ‘LE’ with blue system plug is not compatible with transmitters or receivers of the older sensor type without ‘LE’ with transparent system plug. We recommend replacing the complete VL2 system with the new LE version, as offered here as a complete set.  

combined motion and presence detector, black supply voltage 11.5-32 V DC

reflective photo eye, max. range 12m, supply voltage 24 ... 240 V AC, 50/60 Hz, 12 ... 240 V DC, signal output: changeover relay, IP67 rated, set incl. reflector 84mm, round

airwave switch DW40 normally closed contact in plastic enclosure for doors made by Nassau, Crawford or Assa-AbloyDescription:The Bircher Reglomat DW40 airwave switch is also available in a plastic housing unit for doors made by Nassau, Crawford or Assa-Abloy. The airwave switch converts the airwaves from a signal generator (pushbutton, floor-mounted pressure sensing strip, rubber profile into an electrical switching signal. Just a small amount of pressure of 3 or 4 mbar is enough to ensure the switch generates an electrical signal. Bircher Reglomat's DW-switches have proven reliable millions of times and are installed in a wide variety of applications.PropertiesContact type: Normally Closed Contact (NCC), opens upon contact with the switching mechanismWith connecting terminals and latch plates 6.3mmMounted in an impact-resistant plastic housingHousing unit protection class: IP65 (EN60529)

Plug with resistor, lock cap, fixation clips and end cap (8,2 kOhm)Description:The end cap set KS 4 W 30.70 by ASO Safety is used to assemble SENTIR SE 30.70 type sensing edges. The integrated 8,2 kOhm resistor can be monitored by either an external control unit or, if compatible, directly by the door control unit. The set includes:Plug with resistorLock capFixation clipsEnd cap

Hormann Art. Nr. 638462, pull-in protection EZS / receiver, potting compound: black, IP54, cable length: 1500 mm; production period 01.03.2005 -

Complete set with coil cores, mounting brackets, 20 m steel cable and accessories for internal installation on roller profiles from 130 mm to 190 mm.Description:The ELMON Inductive ISB 11 by ASO Safety is an assembly kit for the signal transmission system ELMON Inductive, for external mounting on the door profile.Technical properties:• Mounting brackets• 20m steel cable• Accessories for internal installation in door roller profiles

Radio-receiver for wireless sensing edge system, for wireless transmission of optical, resistive or mechanical sensing edges, 868 MHz radio frequency, max. range 50m, can be connected to up to 6 transmitters (3 on relay 1, 3 on relay 2), operating temperature -20 ... +55°C

Rubber profile for optical sensing edges, coil of 10m, material EPDM

Component / Replacement part for ELMON InductiveDescription:The ELMON Inductive 70-755 by ASO Safety is a plug-in card for the signal transmission system ELMON Inductive.Technical properties:• Supply voltage 24 V DC• Safety category 2/ PL “d” acc. To EN ISO 13849-1:2008• Plug-in card, without housing