Sensors

Rubber profile for optical sensing edges, coil of 30m, material EPDM

Control unit for monitoring 8k2 resistive sensing edges, in rail-mounted housing, supply voltage: 85-205 V, 24 V AC/DC, 2 channels, safety level Cat. 3/ PL "e"Description:The ELMON 41-622 control unit by ASO Safety is used to monitor the status of 8k2-sensing edges. The unit can monitor a single sensing edge with 8k2 end resistor and indicates its status via one output relay. Properties:• Rail-mounted housing• Supply voltage 85...205V, 24 V AC/DC, +/- 10%• Reaction time < 12 ms• Input: 2 sensing edges, 8.2 kOhm• Output: 2 forcibly guided, relay contacts• Housing: rail-mounted housing for a 35mm DIN-rail• Safety category 3/ PL “e“, acc. to EN ISO 13849-1:2008• Dimensions: 45 x 114 x 99 mm (W x H x D)

Hormann Art. Nr. 638467, light curtain HLG, transmitter and receiver, length 2500 mm; Note: Use as SKS (connection to X30): possible on controllers (360 and 4xx) from 04/2014 (from SW index H) Use in addition to SKS (connection to X 20): possible on controller 360 from 04/2012 (from SW index A) or 4xx from 05/2005 (from SW index C). Not for gates <= 2750 mm RM (L-fitting and N-fitting) or <= 2500 mm RM (H-fitting and V-fitting); 01.04.2014 -

Profile for sensing edge SENTIR Edge 30.70 TT by ASO Safety, width 30mm, height 70mm, roll of 30m Description: The Plug’N’Sense System allows easy assembly of the SENTIR Edge 30.70 TT contact edges by ASO Safety. No additional adhesive or other assembly material is needed. The safety edges can be assembled on site, allowing for tailor made solutions according to the local conditions. As a terminating resistor the end plugs are equipped with an 8k2 ohm resistor, which can be monitored by many of the commercially available gate and door controls. Delivery includes: 30m contact profile SENTIR Edge 30.70 TT, width 30mm, height 70mm On request, we also deliver pre-assembled safety edges according to your desired length. Please send us your requirements and we will make an individual offer.

Hormann Art. No. 635703, Travelling photo eyes VL1-LE, complete set, supplied with sliding plates, range, coverage 6.0 - 10 m Product description: The Hormann VL1-LE sensor system is a 1-beam travelling photo eyes and is used to protect compatible industrial sectional doors. The single-beam photo eye is guided in front of the lower edge of the door by the supplied mechanism and if the light beam is interrupted by an obstacle, the door is stopped and reversed. The ‘LE’ system (grey connection cable with yellow/blue system plug) replaces the old VL1 systems without ‘LE’ (black connection cable with transparent system plug). Note: Identification sensor type ‘LE:’ grey connection cable, production period 01.03.2017 - LE transmitter: blue system plug LE receiver: yellow system plug The sensor type ‘LE’ with blue/yellow system plug is not compatible with transmitters or receivers of the older sensor type without ‘LE’ with transparent system plug. We recommend replacing the complete VL1 system with the new LE version, as offered here as a complete set.

Rubber profile for optical sensing edges, coil of 10m, material EPDM

Component / Replacement part for ELMON InductiveDescription:The ELMON Inductive 70-757 by ASO Safety is a plug-in card for the signal transmission system ELMON Inductive.Technical properties:• Supply voltage 24 V DC• Safety category 2/ PL “d” acc. to EN ISO 13849-1:2008• Plug-in card, without housing

Set of Laser Scanner with protective cover in Aluminium , scanner for presence detection on doors or barrier arms: complete coverage over 4 planes (16560 measurements per second), adjustable via remote control (separate accessory), IP65 rated, 2 output signals, dynamic teach-in, max. range 9,9m x 9,9m, can fulfil requirements of a type-E device according to EN 12453, PL "d"Description:The BEA LZR®-I100 is a sensor for monitoring the closing plane of the door and is certified as a type E device with presence detection according to the EN12453 certification. The sensor functions on time-of-flight technology which enables precise recognition of even the smallest object. The LZR generates laser beams in 4 detection planes to monitor both the closing plane of the door and the area in front it. BEA designed the LZR I100 for industrial environments and can also ensure larger industrial doors are secured thanks to its detection field of up to 9.9m x 9.9m. Together with the BEA LZR laser scanner protective cover, the set is ideally suited for first installations or for retrofitting on existing barrier systems. The scanner is secured in the protective cover and can be easily installed.Details of the LZR-I100:Maximum range 9.9m x 9.9mDepending on the installation height, monitors up to 1m upon approach of the doorEN ISO 13849-1 PL d/CAT 2 and EN 12453 type E certifiedContactless protection of industrial doorsEasy setup and retrofitting of existing facilitiesProtection upon approach and departure (roll-up safety)Up to 2 virtual pushbuttons for opening doorsFilters external interference (door vibrations, snow, rain...)IP 65 protection classThrough the separate use of a universal remote control, it is possible to set up and adjust the sensors from the ground.Details of the protective cover for the BEA LZR laser scanner:The protective cover for the BEA LZR Laser scanner was developed as an accessory for the BEA LZR sensor range. The protective cover is made of a 2.5mm-thick Aluminium sheet and is used protect the sensor and to make the installation inconspicuous. Thanks to its Aluminum protective cover, the scanner can fit in with similar installation environments. Covers coated in several RAL colours are also available upon request to fit in with any environment. The protective cover can be mounted either on the appropriate mounting holes on masonry, barrier housing, etc... or with the help of a mounting bracket, sold separately. The LZR Sensor does not come with the cover and must be ordered separately.Compatible with BEA LZR H-100, LZR-i100 and LZR-i110Aluminum protective cover Anticorrosive thanks to aluminium sheetVersatile installation options

Airwave switch, normally closed contact, with screw terminals, including plastic mounting-base

Control unit for monitoring 8k2 resistive sensing edges, in surface-mounted housing, supply voltage: 230 V, 12-24 V AC/DC, 1 channel, safety Cat. 2/ PL "d"Description:The ELMON 31-31 control unit by ASO Safety is used to monitor the status of 8k2-sensing edges. The unit can monitor a single sensing edge with 8k2 end resistor and indicates its status via one output relay. Properties:• Surface-mounted housing• Supply voltage 230 V, 12 - 24 V AC/DC, +/- 10%• Reaction time < 5 ms• Input: 1 sensing edge, 8.2 kOhm• Output: 1 relay contact• Housing: transparent lid housing• Safety category 2/ PL “e“, acc. to EN ISO 13849-1:2008• Dimensions: 120 x 100 x 57 mm (W x H x D)

Loop detector for 2 loops 230 VAC, for DIN-rail mount with plug-in base (mount and base not included)

Dual-Technology sensor for the opening and presence detection on doors, for automatic standard and emergency exit doors, in conformity with DIN EN16005, detection field 4m (W) x 4m (D), opening by radar motion detector, presence detection via a 3-row infrared safety curtain, cross-traffic filter, direction-sensitive opening sensor, max. installation height 3.5m.Description:The SSR-3-ER from HOTRON is a 3-in-1 sensor for the activation and safeguarding of standard doors (relay output) or emergency exit doors (current output / frequency output). Due to this wide range of functions, this sensor is suitable for all types or sliding doors.The Infrared security curtains contain three detection rows which protect persons in and around the closing area. The direction-sensitive detection technology is responsible for a reduction of up to 20% a building’s energy loss. Through its intelligent cross-traffic filter, the unintended activation of doors caused by pedestrians walking parallel to the door is clearly reduced.For easy mounting and installation on site, the manufacturer has printed the installation instructions clearly on the body of the sensor. The dip switch setting, pre-set at the factory, fulfils the requirements of EN16005. The sensor body, which comes in one-piece, prevents the loss or damage of parts during installation.

Rubber profile for optical sensing edges, coil of 5m, material EPDM

Profile for sensing edge SENTIR Edge 35.55 CT by ASO Safety, width 35mm, height 55mm, roll of 30m Description: The Plug’N’Sense System allows easy assembly of the SENTIR Edge 35.55 CT contact edges by ASO Safety. No additional adhesive or other assembly material is needed. The safety edges can be assembled on site, allowing for tailor made solutions according to the local conditions. As a terminating resistor the end plugs are equipped with an 8k2 ohm resistor, which can be monitored by many of the commercially available gate and door controls. Delivery includes: 30m contact profile SENTIR Edge 35.55 CT, width 35mm, height 55mm On request, we also deliver pre-assembled safety edges according to your desired length. Please send us your requirements and we will make an individual offer.

Dual technology sensor for opening and presence detection on automatic sliding doors, sensor for standard doors, pulsed monitoring, digital adjustment of the radar field shape, automatic recalibration of the radar signal for FRW doors in difficult environments and in particular narrow wind gaps

Witt Sensoric photo eye Bilix 10, output: 2-wire, range, coverage 7 m for indoor areas

ELS 263 photo eye, receiver, output: NPN/LO , with connection cable, length 5.0m

ELS 263 photo eye, receiver, output: PNP/DO , with connection cable, length 5.0m

ELS 263 photo eye, receiver, output: NPN/DO , with connection cable, length 5.0m

The RDS 100 radar detector from CEDES is suitable for mounting heights of 1.8 - 4.0 metres. With a large detection area of 4 x 2m at a mounting height of 2.2m, people and objects are reliably detected.Features: Simple installation without expensive mounting kits Adjustable detection angle Large detection area Very compact sensor  

Time-of-flight (TOF) sensor, for presence detection, range, coverage from 0.2 m to 6 m, Supply voltage 10-30 V DC, detection area 20x20mm at 2m installation height, setting via "Teach-In", universal output (relay, PNP, NPN) Connection cable 0.25m

Technical details:ELS 500 SY, through-beam sensor, transistor output PNP, function: LO - Light On, cable length 20m, set consisting of transmitter and receiverProduct description:The ELS 500 single light barrier from CEDES is your ideal solution for safeguarding industrial doors. Thanks to its robust metal housing, it is ideal for use in extremely harsh environments.Product features: Adjustable range, coverage: Up to 20 metres Easy to install: M12 thread for effortless integration into any door profile Robust and resistant: IP67 design for reliable operation in environments with water, high humidity or dust High interference immunity: Impervious to electromagnetic fields Flexible output types: Available in NPN and PNP, both light and dark switching Advantages of the ELS 500 photo eye: Reliability: Proven solution for safeguarding industrial doors Use in harsh environments: Thanks to the robust metal housing and IP67 design Easy integration: Thanks to the adjustable range, coverage and M12 thread Interference-free: Complies with all common industry standards and is impervious to electromagnetic fields  

Description:The BEA 1SAFE is an active infrared sensor with background suppression (triangulation) that is suitable for all door types. With a detection field of 35 × 70 mm at an installation height of 2.20 m, the 1SAFE offers precise and concentrated coverage. This sensor is ideal for opening, securing or monitoring doors and ensures reliable safety and convenience.Product features:The BEA 1SAFE is characterised by its ability to track and record the evolution of its background and surroundings, ensuring high reliability and precision in door monitoring. It provides protection for various door types: Linear sliding doors it safeguards when opening and prevents crushing hazards, revolving doors and swing doors it protects against terminal block or crushing hazards when closing, and on revolving doors it safeguards the main closing edge where no other monitoring is possible.Thanks to its narrow detection field, the 1SAFE is ideal as an alternative to push plates and can also open automatic doors in narrow detection zones, such as in restaurant kitchens or in the interior doors of trains. For the most common applications and installation heights, the detection zone can be adjusted in automatic mode at the simple press of a button. In addition, the manual mode allows precise adjustment of the detection zone for special applications such as large installation heights, reflective floor coverings or horizontal applications using adjustment screws and DIP switches.

The DualSense D from BBC Bircher Smart Access is a sophisticated sensor that has been specially developed for the activation and safety of automatic sliding doors. This sensor fulfils the requirements of the EN 16005 standard and is therefore also suitable for emergency exits.Features:  Two-in-one technology: the DualSense D combines a radar motion sensor module for door opening and an active infrared presence detector module (AIR) to protect people in the area of door movement. Adaptability: The radar modules can be fully customised to the respective environment to avoid interference. The settings for field dimensions, field alignment, direction detection and filtering can be easily adjusted. Energy efficiency: The ability to ignore passing objects prevents unwanted door openings, which reduces the building's energy consumption. Easy installation: The intuitive operating concept with user-friendly menu navigation and a large display enables quick and easy installation.     Versatility: The AIR modules provide protection at the main closing edges of the door and can be customised depending on the installation height and floor covering. Specific requirements can be met by adjusting the sensitivity and teach-in time. Robust design: The sensor is available in three different colours (black, white, silver) and is made of durable ABS/PA housing material. With a protection rating of IP54, it is ideally suited for use in various environments. The DualSense D offers a reliable and user-friendly solution for controlling and securing automatic sliding doors and is ideal for use in escape routes and emergency exits.